Free Shipping  within main land UK on all orders over £20.
PACE FS-HDP4102P Single Channel HD Passive Video Balun Screw Terminal 2 pack

PACE FS-HDP4102P Single Channel HD Passive Video Balun Screw Terminal 2 pack

PACE HDP4102C Single Channel HD Passive Video Balun Screw Terminal 2 pack

PACE HDP4102C Single Channel HD Passive Video Balun Screw Terminal 2 pack

PACE FS-HDP4102P Single Channel HD Passive Video Balun Screw Terminal 2 pack

£28.79 £23.99
Availability: Out of stock
SKU
FS-HDP4102P X 10
  •  

    The FS-HDP4102P video balun is a passive (non-amplified) device that allows the transmission of real-time CCTV HD video  signal via cost-effective Unshielded Twisted Paired (UTP) cable. The FS-HDP4102P is compatible with all HD-TVI, HD-CVI, AHD and CVBS analog cameras.

    The FS-HDP4102P has a mini-coax pigtail lead which allows quick mounting onto fixed cameras, allows in-camera mounting in most dome cameras and allows flexible connection with DVR. Push-pin terminal block allows tool-less connection of UTP cable output.Used in pairs, the FS-HDP4102P eliminates costly and bulky coaxial cable..

    The superior interference rejection and low emissions of the FS-HDP4102P allow video signals to coexist in the same wire bundle as telephone, datacom, or low-voltage power circuits. This allows the use of a shared or existing cable plant. The FS-HDP4102P is built-in surge suppressor to protect video equipment against damaging voltage spikes. Its crosstalk and noise immunity ensure quality video signals.

     

    Note:

    1. The actual transmission distance will vary according to the quality of the cable, specific camera, and on-site environment.

    2. Please make sure to install transmitter at camera side and receiver at DVR side to achieve best video quality.

    3. If you adjust saturation of DVR, video transmission distance could be farther. HD-CVI 720P: max up to 470m (1541ft).

    4. If chromatic aberration occurs, please also adjust saturation, the picture will recover perfectly automatically.

    5. The device is not waterproof and not to be used at outdoors.

    Wire and Cable Recommendations

    The FS-HDP4102P is recommended to use with Unshielded Twisted Paired (UTP) wiring from 24AWG through 22AWG.

    Individually shielded pairs should be avoided, as they reduce the operating range of the systems drastically.

    Multi-pair cable (25-pair or more) with an overall shield is acceptable. Video signals can coexist in the same wire bundle as telephone, data-com, or low-voltages power circuits.

    While video may be routed through telephone punch-down block terminals, any bridge-taps, also called T-taps and any resistive, capacity or inductive devices MUST BE removed from the pair.

    For more specific information regarding wire types, gauges and proper installation techniques, please contact us for technical assistance.

    • Real-time transmission over UTP cat5e/6
    • No power required
    • Compatible with all HD-TVI/CVI/AHD/CVBS analog cameras
    • Please refer to “Transmission Distance Chart” Part to find out distance of 720P/960P/1080P/3MP/4MP/5MP/4K cameras
    • Male BNC connector with extended mini-coax pigtail
    • Built-in solid state TVS (Transient Voltage Suppressor) for surge protection 
    • Wave Filter Design, Anti-Static Design
    • Lightning protection design Grade: ?
    • 60 dB crosstalk and noise immunity
    • Exceptional interference rejection
    • ABS engineering plastic housing
    Technical Specifications

                Model

     FS-HDP4102P

                        Product Name

    Single Channel HD Passive Video Balun

                         Applied Devices

    CCTV cameras, monitors, DVR, switchers, IP encoders, and other CCTV equipment

    Video

    Video Format

    HD-TVI/ CVI/AHD /CVBS

    Operating Frequency

    DC to 71MHz

    Common-mode/Differential-mode rejection

                15KHz to 71MHz  60 dB typ.

    Impedance

    Coax: Male BNC  75Ω unbalanced

    UTP: screw terminal   100Ω balanced

    Attenuation

    1.5 dB typ. Max

    Wire Type

    Network Wiring

    One Unshielded Twisted Pair (for each video signal) 24-16 AWG (0.5-1.31mm)

    Category Type

    UTP cat 5e/6

    Impedance

    100 ± 20 ohms

    DC Loop Resistance

    52 ohms per 1,000ft (18 ohms per 100m)

    Differential Capacitance

    19 pF/ft max (62 pF/m max)

                                    Power

    No external power required

    Connector

    Video input/output

    Male BNC connector

    Video input/output

    Screw terminal

    Protection

    Surge Protection

    renewable solid state surge protection

    Video Input

    2KV (common mode), 10/700us IEC61000-4-5/1955(GB/T 1726, 5-1999)

    Video Output

    2KV (differential mode), 10/700us IEC61000-4-5/1955(GB/T 1726, 5-1999)

    Mechanical

    Housing

    ABS engineering plastic

    Body Color

    Black

    Dimensions (L*W*H)

    42.4*17.8*17.4mm (BNC connector & cable excluded)

    Net Weight

    40g

    Environmental

    Operating Temperature

    -20º ~ 70º C

    Relative Humidity

    0~95% (non-condensing)

    Storage Temperature

    -40º ~ 150º C

More Information
Manufacturer PACE
Product Name PACE FS-HDP4102P Single Channel HD Passive Video Balun Screw Terminal 2 pack
SKU FS-HDP4102P X 10
Shipping For Product 0.000000
Calculate Shipping Per Product Quantity
Enable Shipping Per Product Yes
Write Your Own Review
You're reviewing:PACE FS-HDP4102P Single Channel HD Passive Video Balun Screw Terminal 2 pack
Your Rating